8x1000T@8xPoE+, 2xSFP, Managed -40...+75C, IP30, Modbus, ONVIF, DI/DO, DIN

PLANET IGS-10020HPT on teollisuuskäyttöön soveltuva 10- porttinen hallittava 10/100/1000 (8x TX + 2x SFP) High PoE Ethernet- kytkin laajennetulla käyttölämpötila-alueella sekä DIN-kiskokiinnityksellä.

Kytkin on varustettu "PD keep-alive" ominaisuudella, jolla kytkin pystyy itsenäisesti tarkistamaan esim. IP-kameran tilan ping-komennolla ja tekemään portille automaattisen virtakäynnistyksen (PoE OFF -> PoE ON).

Tekniset tiedot: – 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with IEEE802.3at PoE+ Injector – 2x 100/1000/2500BASE-X mini-GBIC/SFP slots for SFP type auto detection – 1x RJ45 console interface for basic management and setup (IGS-10020HPT) – Complies with IEEE 802.3at Power over Ethernet Plus/end- span PSE – Up to 8x IEEE 802.3af/802.3at devices powered – Supports PoE power up to 36W for each PoE port – Auto detects powered device (PD) – Circuit protection prevents power interference between ports – Remote power feeding up to 100m in standard mode and 200m in extend mode – PoE management features – PoE admin-mode control – PoE management mode selection – Per port PoE function enable/disable – PoE port power feeding priority – Per PoE port power limit – PoE Port Status monitoring – PD classification detection – Sequence port PoE – Intelligent PoE features – PoE Legacy mode enable/disable – Temperature threshold control – PoE usage threshold control – PoE schedule – PD alive check – LLDP PoE Neighbors – Industrial Protocol – Modbus TCP for real-time monitoring in a SCADA system – IEEE 1588v2 PTP (Precision Time Protocol) – Industrial Case and Installation – IP30 aluminum case – DIN rail and wall-mount designs – 12-48DCV, redundant power with reverse polarity protection– Supports 6000VDC Ethernet ESD protection – -40...+75C operating temperature – E-Mark certification – 2x Digital Input (DI) – 2x Digital Output (DO) – Integrate sensors into auto alarm system – Transfer alarm to IP network via email and SNMP trap – Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) – High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth – Storm Control support – Broadcast/Multicast/Unicast – Supports VLAN – IEEE 802.1Q tagged VLAN – Supports provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) – Private VLAN Edge (PVE) – Port Isolation – MAC-based VLAN – Protocol-based VLAN – Voice VLAN – GVRP – Supports Spanning Tree Protocol – IEEE 802.1D Spanning Tree Protocol (STP) – IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) – IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN – BPDU Guard – Supports Link Aggregation – 802.3ad Link Aggregation Control Protocol (LACP) – Cisco ether-channel (static trunk) – Maximum 5 trunk groups with 10 ports per trunk group – Up to 20Gbps bandwidth (duplex mode) – Provides port mirror (many-to-1) – Port mirroring to monitor the incoming or outgoing trafficon a particular port – Loop protection to avoid broadcast loops – Supports ERPS (Ethernet Ring Protection Switching) – Compatible with Cisco Uni-directional link detection(UDLD)that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices – Link Layer Discovery Protocol (LLDP) and LLDP-MED – Provides ONVIF for co-operating with PLANET video IP surveillances – Layer 3 IP Routing Features – Supports maximum 32 static routes and route summarization – Quality of Service – Ingress Shaper and Egress Rate Limit per port bandwidth control – 8x priority queues on all switch ports – Traffic classification – IEEE 802.1p CoS – IP TOS/DSCP/IP precedence – IP TCP/UDP port number – Typical network application – Strict priority and Weighted Round Robin (WRR) CoS policies – Supports QoS and In/Out bandwidth control on each port – Traffic-policing policies on the switch port – DSCP remarking – Multicast – Supports IPv4 IGMP snooping v1, v2 and v3 – Supports IPv6 MLD snooping v1 and v2 – Querier mode support – IPv4 IGMP snooping port filtering – IPv6 MLD snooping port filtering – Multicast VLAN Registration (MVR) support – Security – Authentication – IEEE 802.1x Port-based/MAC-based network access authentication – Built-in RADIUS client to co-operate with the RADIUS servers – TACACS+ login users access authentication – RADIUS/TACACS+ users access authentication – Access Control List – IP-based Access Control List (ACL) – MAC-based Access Control List – Source MAC/IP address binding – DHCP Snooping to filter un-trusted DHCP messages – Dynamic ARP Inspection discards ARP packets with invalid – MAC address to IP address binding – IP Source Guard prevents IP spoofing attacks – IP address access management to prevent unauthorized intruder – Management – IPv4 and IPv6 dual stack management – Switch Management Interfaces – Console/Telnet Command Line Interface – Web switch management – SNMP v1, v2c, and v3 switch management – SSHv2 and TLSv1.2 secure access – IPv6 IP Address/NTP/DNS management – Built-in Trivial File Transfer Protocol (TFTP) client – BOOTP and DHCP for IP address assignment – System Maintenance – Firmware upload/download via HTTP – Reset button for system reboot or reset to factory default– Dual Images – DHCP Relay – DHCP Option82 – DHCP Server Mode support – User Privilege levels control – NTP (Network Time Protocol) – Link OAM – Network Diagnostic – ICMPv6/ICMPv4 Remote Ping – Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues – SMTP/Syslog remote alarm – Four RMON groups (history, statistics, alarms and events) – SNMP trap for interface Link up and Link down notification– System Log – SFP-DDM (Digital Diagnostic Monitor) – PLANET Smart Discovery Utility for deployment management – PLANET NMS system and CloudViewer for deployment