8x100/1000T PoE++ +2x10G SFP, -40...+75C Industrial Switch, SNMP, L3, IP30

PLANET IGS-6325-8UP2S on teollisuuskäyttöön suunniteltu 12-porttinen hallittava DIN-kiskoon asennettava UltraPoE Etehernet-kytkin laajennetulla käyttölämpötila-alueella. L3
-kytkin on varustettu 8x 10/100/1000Base-T PoE++ kupariporteilla, 2x 100/1000/2, 5G SFP-portilla sekä 2x 10G SFP+ moduulipaikoilla. Kytkimessä on lisäksi kehittyneemmät hallintapuolen turvaominaisuudet sekä IEEE 1588 aikaprotokollatuki aikakriittisisiin sovelluksiin.

Tekniset tiedot – 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with 802.3bt PoE++ Injector function – 2x 100/1000BASE-X SFP slots for SFP type auto detection – 2x 10GBASE-SR/LR SFP+ slots, compatible with 1000/2500BASE-X SFP – One RJ45-to-RS232 console interface for basic management and setup – Dual power input, redundant power with reverse polarity protection
- DC 48 to 56V input
- Active-active redundant power failure protection
- Backup of catastrophic power failure on one supply
- Fault tolerance and resilience – DIN-rail and wall-mountable design – IP30 aluminum case – Supports 6000V DC Ethernet ESD protection – -40...+75C operating temperature – 2x Digital Input (DI) – 2x Digital Output (DO) – Integrate sensors into auto alarm system – Transfer alarm to IP network via email and SNMP trap – Complies with IEEE 802.3bt Power over Ethernet Plus Plus Type-4 PSE – Backward compatible with IEEE 802.3at/af PD device – Up to 8 ports of IEEE 802.3af/IEEE 802.3at/IEEE 802.3bt PoE++ devices powered – Supports PoE power up to 95 watts for each PoE port – Total of 360-watt PoE budget – Auto detects powered device (PD) – Circuit protection prevents power interference between ports – Remote power feeding up to 100m – PoE management features
- Total PoE power budget control
- Per port PoE function enable/disable
- PoE admin-mode control
- PoE port power feeding priority
- Per PoE port power limit
- PD classification detection
- PoE extend mode control to support power feeding up to a distance of up to 160 meters – Intelligent PoE features
- Temperature threshold control
- PoE usage threshold control
- PD alive check
- PoE schedule – IP dynamic routing protocol supports OSPFv2 – IPv4/IPv6 hardware static routing – Routing interface provides per VLAN routing mode – High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth – Storm Control support
- Broadcast/Multicast/Unicast – Supports VLAN
- IEEE 802.1Q tagged VLAN
- Up to 255 VLANs groups, out of 4095 VLAN IDs
- Supports provider bridging (VLAN Q-in-Q IEEE 802.1ad)
- Private VLAN Edge (PVE)
- Protocol-based VLAN
- MAC-based VLAN
- Voice VLAN
- GVRP (GARP VLAN Registration Protocol) – Supports Spanning Tree Protocol
- IEEE 802.1D Spanning Tree Protocol (STP)
- IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
- IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
- BPDU Guard – Supports Link Aggregation
- 802.3ad Link Aggregation Control Protocol (LACP)
- Cisco ether-channel (static trunk)
- Maximum 4 trunk groups with 4 ports per trunk group
- Up to 40Gbps bandwidth (duplex mode) – Provides port mirror (many-to-1) – Port mirroring to monitor the incoming or outgoing trafficon a particular port – Loop protection to avoid broadcast loops – Link Layer Discovery Protocol (LLDP) – Compatible with Cisco uni-directional link detection(UDLD)that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices – Supports G.8032 ERPS (Ethernet Ring Protection Switching) – IEEE 1588 and Synchronous Ethernet network timing – Ingress Shaper and Egress Rate Limit per port bandwidth control – 8x priority queues on all switch ports – Traffic classification
- IEEE 802.1p CoS
- IP TOS/DSCP/IP precedence
- IP TCP/UDP port number
- Typical network application – Strict priority and Weighted Round Robin (WRR) CoS policies – Supports QoS and In/Out bandwidth control on each port – Traffic-policing on the switch port – DSCP remarking – Supports IPv4 IGMP snooping v1, v2 and v3 – Supports IPv6 MLD snooping v1 and v2 – Querier mode support – IPv4 IGMP snooping port filtering – IPv6 MLD snooping port filtering – MVR (Multicast VLAN Registration) – Authentication
- IEEE 802.1X Port-based/MAC-based network access authentication
- Built-in RADIUS client to cooperate with the RADIUS servers
- TACACS+ login users access authentication
- RADIUS/TACACS+ users access authentication
- Guest VLAN assigns clients to a restricted VLAN with limited services – Access Control List
- IP-based Access Control List (ACL)
- MAC-based Access Control List – Source MAC/IP address binding – DHCP snooping to filter distrusted DHCP messages – Dynamic ARP Inspection discards ARP packets with invalid – MAC address to IP address binding – IP Source Guard prevents IP spoofing attacks – IP address access management to prevent unauthorized intruder – IPv4 and IPv6 dual stack management – Switch Management Interfaces
- Console and Telnet Command Line Interface
- HTTP web switch management
- SNMP v1 and v2c switch management
- SSH, TLS, SSL and SNMP v3 secure access – SNMP Management
- Four RMON groups (history, statistics, alarms, and events)
- SNMP trap for interface Link Up and Link Down notification– IPv6 IP address/NTP/DNS management – Built-in Trivial File Transfer Protocol (TFTP) client – BOOTP and DHCP for IP address assignment – System Maintenance
- Firmware upload/download via HTTP/TFTP
- Reset button for system reboot or reset to factory default
- Dual Images – DHCP Relay – DHCP Option 82 – DHCP Server