8x1000T@8xPoE+, 2xSFP, 2xSFP+10G, Managed L3 -40...+75C, IP30, DI/DO, DIN

PLANET IGS-5225-8P2S2X on teollisuuskäyttöön suunniteltu 12-porttinen hallittava DIN-kiskoon asennettava PoE+ kytkin laajennetulla käyttölämpötila-alueella. L3-kytkin on varustettu 8x 10/100/1000Base-T PoE+ kupariportilla, 2x 100/1000 SFP-portilla sekä 2x 10G SFP+ portilla (100/1000 alhteensopivat).

Tekniset tiedot – 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with IEEE802.3at PoE+ Injector function – 2x 100/1000/2500BASE-X mini-GBIC/SFP slots for SFP type auto detection – 2x 10GBASE-SR/LR SFP+ slots, backward compatible with 1000BASE-SX/LX/BX and 2500BASE-X SFP – One RJ45 console interface for basic management and setup – Complies with IEEE 802.3at Power over Ethernet Plus/end- span PSE – Up to 8x IEEE 802.3af/802.3at devices powered – Supports PoE power up to 36 watts for each PoE port – Auto detects powered device (PD) – Circuit protection prevents power interference between ports – Remote power feeding up to 100m – PoE management features – Total PoE power budget control – Per port PoE function enable/disable – PoE admin-mode control – PoE port power feeding priority – Per PoE port power limit – PD classification detection – Intelligent PoE features – Temperature threshold control – PoE usage threshold control – PD alive check – PoE schedule – Industrial Protocol – Modbus TCP for real-time monitoring in the SCADA system – IEEE 1588v2 PTP (Precision Time Protocol) – Industrial Case and Installation – IP30 aluminum case – DIN-rail and wall-mount designs – 48...56VDC, redundant power with reverse polarity protection – Supports 6000VDC Ethernet ESD protection – -40...+75C operating temperature – 2x Digital Input (DI) – 2x Digital Output (DO) – Integrate sensors into auto alarm system – Transfer alarm to IP network via email and SNMP trap – Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) – High performance of Store-and-Forward architecture, and runt/CRC filtering that eliminates erroneous packets to optimize the network bandwidth – Storm Control support – Broadcast/Multicast/Unicast – Supports VLAN – IEEE 802.1Q tagged VLAN – Up to 4K VLANs groups, out of 4095 VLAN IDs – Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) – Private VLAN Edge (PVE) – Protocol-based VLAN – MAC-based VLAN – Voice VLAN – GVRP (GARP VLAN Registration Protocol) – Supports Spanning Tree Protocol – IEEE 802.1D Spanning Tree Protocol (STP) – IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) – IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN – BPDU Guard – Supports Link Aggregation – 802.3ad Link Aggregation Control Protocol (LACP) – Cisco ether-channel (static trunk) – Maximum 6 trunk groups with 4 ports per trunk group – Up to 16Gbps bandwidth (duplex mode) – Provides port mirror (many-to-1) – Port mirroring to monitor the incoming or outgoing trafficon a particular port – Loop protection to avoid broadcast loops – Supports ERPS (Ethernet Ring Protection Switching) – Compatible with Cisco Uni-directional link detection(UDLD)that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices – Link Layer Discovery Protocol (LLDP) – Layer 3 IP Routing Features – Supports maximum 128 static routes and route summarization– IPv4 dynamic routing protocol supports OSPFv2 – IPv4/IPv6 hardware static routing – Routing interface provides per VLAN routing mode – Quality of Service – Ingress Shaper and Egress Rate Limit per port bandwidth control – 8 priority queues on all switch ports – Traffic classification – IEEE 802.1p CoS – TOS/DSCP/IP precedence of IPv4/IPv6 packets – IP TCP/UDP port number – Typical network application – Strict priority and Weighted Round Robin (WRR) CoS policies – Supports QoS and In/Out bandwidth control on each port – Traffic-policing policies on the switch port – DSCP remarking – Multicast – Supports IGMP snooping v1, v2 and v3 – Supports MLD snooping v1 and v2 – Querier mode support – IGMP snooping port filtering – MLD snooping port filtering – Multicast VLAN Registration (MVR) support – Security – Authentication – IEEE 802.1x Port-based / MAC-based network access authentication – Built-in RADIUS client to co-operate with the RADIUS servers – TACACS+ login users access authentication – RADIUS / TACACS+ users access authentication – Access Control List – IP-based Access Control List (ACL) – MAC-based Access Control List – Source MAC / IP address binding – DHCP Snooping to filter un-trusted DHCP messages – Dynamic ARP Inspection discards ARP packets with invalid – MAC address to IP address binding – IP Source Guard prevents IP spoofing attacks – IP address access management to prevent unauthorized intruder – Management – IPv4 and IPv6 dual stack management – Switch Management Interfaces – Console/Telnet Command Line Interface – Web switch management – SNMP v1 and v2c switch management – SSH, TLS, SSL and SNMP v3 secure access – SNMP Management – Four RMON groups (history, statistics, alarms, and events)– SNMP trap for interface Link Up and Link Down notification– IPv6 IP address/NTP/DNS management – Built-in Trivial File Transfer Protocol (TFTP) client – BOOTP and DHCP for IP address assignment – System Maintenance – Firmware upload/download via HTTP/TFTP – Reset button for system reboot or reset to factory default– Dual Images – DHCP Relay and DHCP Option 82 – DHCP Server – User Privilege levels control – Network Time Protocol (NTP) – SFP-DDM (Digital Diagnostic Monitor) – Network Diagnositc – ICMPv6/ICMPv4 Remote Ping – Cable diagnostic technology provides the mechanism to detect and report potential cabling issues – PLANET NMS System and Smart Discovery Utility for deployment management – SMTP/Syslog remote alarm – System Log