8x1000T@8xPoE+, 4xSFP, Managed L3 -40...+75C, IP30, DI/DO, ONVIF, DIN

PLANET IGS-5225-8P4S on teollisuuskäyttöön suunniteltu 12-porttinen hallittava DIN-kiskoon asennettava PoE+ kytkin laajennetulla käyttölämpötila-alueella. L3-kytkin on varustettu 8x 10/100/1000Base-T PoE+ kupariportilla sekä 4x 100/1000 SFP-portilla.

Tekniset tiedot – 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 port switch IEEE 802.3at PoE+ Injector – 2x 100/1000BASE-X SFP ports for SFP type auto detection – 2x 100/1000/2500BASE-X SFP ports for SFP type auto detection – One RJ45 console interface for basic management and setup – Power over Ethernet – Complies with IEEE 802.3at Power over Ethernet Plus/end- span PSE – Up to 8 IEEE 802.3af/802.3at devices powered – Supports PoE power up to 36 watts for each PoE port – Auto detects powered device (PD) – Circuit protection prevents power interference between ports – Remote power feeding up to 100m – PoE management features – PoE admin-mode control – PoE management mode selection – PoE legacy mode selection – PoE budget setup option – Per port PoE function enable/disable – PoE port power feeding priority – Per PoE port power limit – PoE port status monitoring – PD classification detection – Sequence port PoE – PoE extend mode control to support power feeding up to a distance of up to 160 meters – Intelligent PoE features – Temperature threshold control – PoE usage threshold control – PoE schedule – PD alive check – LLDP PoE Neighbors – Industrial Protocol – Modbus TCP for real-time monitoring in the SCADA system – IEEE 1588v2 PTP (Precision Time Protocol) transparent clock mode – Industrial Case and Installation – IP30 aluminum case – DIN-rail or wall-mount design – 48...56VDC, redundant power with reverse polarity protection – Supports 6KV DC Ethernet ESD protection – -40...+75C operating temperature – Digital Input and Digital Output – 2x digital input (DI) – 2x digital output (DO) – Integrate sensors into auto alarm system – Transfer alarm to IP network via email and SNMP trap – Layer 3 IP Routing Features – Supports maximum 32 static routes and route summarization – Routing interface provides per VLAN routing mode – Layer 2 Features – Storm Control support – Broadcast / Multicast / Unicast – Supports VLAN – IEEE 802.1Q tagged VLAN – Supports provider bridging (VLAN Q-in-Q, IEEE 802.1ad) – Private VLAN Edge (PVE) – Port Isolation – MAC-based VLAN – IP Subnet-based VLAN – Protocol-based VLAN – VLAN Translation – Voice VLAN – GVRP – Supports Spanning Tree Protocol – IEEE 802.1D Spanning Tree Protocol (STP) – IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) – IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN – BPDU Filtering/BPDU Guard – Supports Link Aggregation – 802.3ad Link Aggregation Control Protocol (LACP) – Cisco ether-channel (static trunk) – Maximum 6 trunk groups with 4 ports per trunk group – Up to 8Gbps bandwidth (duplex mode) – Provide sport mirror (many-to-1) – Port mirroring to monitor the incoming or outgoing trafficon a particular port – Loop protection to avoid broadcast loops – Supports ERPS (Ethernet Ring Protection Switching) – Compatible with Cisco Uni-directional link detection(UDLD)that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices – Link Layer Discovery Protocol (LLDP) – IEEE 802.3ah OAM – Quality of Service – Ingress Shaper and Egress Rate Limit per port bandwidth control – 8 priority queues on all switch ports – Traffic classification – IEEE 802.1p CoS – IP TOS/DSCP/IP precedence – IP TCP/UDP port number – Typical network application – Strict priority and Weighted Round Robin (WRR) CoS policies – Supports QoS and In/Out bandwidth control on each port – Traffic-policing on the switch port – DSCP remarking – Multicast – SupportsIPv4 IGMP snooping v1, v2 and v3 – Supports IPv6 MLD snooping v1 and v2 – Querier mode support – IPv4 IGMP snooping port filtering – IPv6 MLD snooping port filtering – MVR (Multicast VLAN Registration) – Security – Authentication – IEEE 802.1x port-based/MAC-based network access authentication – Built-in RADIUS client to co-operate with the RADIUS servers – TACACS+ login users access authentication – RADIUS / TACACS+ users access authentication – Guest VLAN assigns clients to a restricted VLAN with limited services – Access Control List – IP-based Access Control List (ACL) – MAC-based Access Control List – Source MAC/IP address binding – DHCP Snooping to filter un-trusted DHCP messages – Dynamic ARP Inspection discards ARP packets with invalid – MAC address to IP address binding – IP Source Guard prevents IP spoofing attacks – IP address access management to prevent unauthorized intruder – Management – IPv4 and IPv6 dual stack management – Switch Management Interfaces – Web switch management – Console and Telnet Command Line Interface – SNMP v1 and v2c switch management – SSHv2, TLSv1.2 and SNMPv3 secure access – SNMP Management – Four RMON groups (history, statistics, alarms, and events)– SNMP trap for interface Link Up and Link Down notification– IPv6 IP Address/NTP/DNS management – Built-in Trivial File Transfer Protocol (TFTP) client – BOOTP and DHCP for IP address assignment – System Maintenance – Firmware upload/download via HTTP – Reset button for system reboot or reset to factory default– Dual Images – DHCP Relay and DHCP Option82 – DHCP Server – User Privilege levels control – NTP (Network Time Protocol) – UPnP – Network Diagnostic – ICMPv6/ICMPv4 Remote Ping – Cable Diagnostic technology provides the mechanism to detect and report potential cabling issues – SFP-DDM (Digital Diagnostic Monitor) – SMTP, Syslog and SNMP trap remote alarm – Local system Log – PLANET NMS System and Smart Discovery Utility for deployment management – Provides ONVIF for co-operating with PLANET video IP surveillances