PLANET IGS-6325-4UP2X on 6-porttinen 10 Gigabitin hallittava DIN-kiskoon asennettava Ultra PoE (802.3bt) Etehernet-kytkin laajennetulla käyttölämpötila-alueella. L3-kytkin on varustettu 4x 100M/1G/2.5G kupariportilla sekä 2x 1G/2.5G/10G SFP/SFP+ moduulipaikalla.

Tekniset tiedot – 4x 10/100/1G/2.5GBASE-T RJ45 copper ports with 802.3bt PoE++ Injector function – 2x 10GBASE-SR/LR SFP+ slots, compatible with 1G/2.5GBASE-XSFP – 1x RJ45-to-RS232 console interface for basic management and setup – Ruggedly Reliable – Dual power input, redundant power with reverse polarity protection – 48…54VDC input – Active-active redundant power failure protection – Backup of catastrophic power failure on one supply – Fault tolerance and resilience – DIN-rail and wall-mount designs – IP30 aluminum case – Supports 4KVDC Ethernet ESD protection. – -40…75C operating temperature – 2x digital inputs (DI) – 2x digital outputs (DO) – Integrates sensors into auto alarm system. – Transmits alarm to IP network via email and SNMP trap – IEEE 802.3bt Power over Ethernet – Compliance with IEEE 802.3bt Type-4 PoE++ standard – Backward compatibility with IEEE 802.3at/af PD device – Powers up to four IEEE 802.3bt PoE++ devices (backward compatible with IEEE 802.3af/at) – Supports PoE with power up to 95W for each PoE port. – Total of 360W PoE budget – A single power input can provide a power budget of up to 240W – Two power inputs can provide a power budget of up to 360W.– Detects Powered Devices (PD) automatically. – Circuit protection prevents power interference between ports – Power feeding up to 100m – PoE management features – Total PoE power budget control – Per port PoE function enable/disable – PoE admin-mode control – PoE port power feeding priority – Per PoE port power limit – PD classification detection – PoE extension mode to support power feeding up to a maximum distance of 160 meters – Intelligent PoE features – Temperature threshold setting – PoE usage threshold setting – PD alive check – PoE schedule – Layer 3 IP Routing Features – IPv4 dynamic routing protocol supports RIPv2 and OSPFv2 – IPv6 dynamic routing protocol supports OSPFv3. – IPv4/IPv6 hardware static routing – The routing interface provides a per-VLAN routing mode – Layer 2 Features – The Store-and-Forward architecture offers high performance, while the runt/CRC filtering eliminates erroneous packets to optimize network bandwidth. – Storm control support – Broadcast/Multicast/Unknown unicast – VLAN support includes: – IEEE 802.1Q tagged VLAN – Provider bridging (VLAN Q-in-Q IEEE 802.1ad) – Private VLAN Edge (PVE) – Protocol-based VLAN – MAC-based VLAN – Voice VLAN – GVRP (GARP VLAN Registration Protocol) – Supports Spanning Tree Protocol including: – IEEE 802.1D Spanning Tree Protocol (STP) – IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) – IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN – BPDU Guard – Supports Link Aggregation including: 802.3ad Link Aggregation Control Protocol (LACP: 6 ports/3 groups max.) – Cisco ether-channel (static trunk: 6 ports/3 groups max.) – Provides port mirror (Many-to-1) – Port mirroring to monitor the incoming or outgoing trafficon a particular port – Loop protection to avoid broadcast loops – Link Layer Discovery Protocol (LLDP) – Compatible with Cisco Uni-Directional Link Detection (UDLD), which monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices. – Supports G.8032 ERPS (Ethernet Ring Protection Switching).– Supports IEEE 1588v2 PTP (Precision Time Protocol) transparent clock mode. – Quality of Service – Ingress shaper and egress rate limit per port bandwidth control – 8x priority queues on all switch ports – Traffic classification – IEEE 802.1p CoS – ToS/DSCP/IP Precedence of IPv4/Ipv6 packets – IP TCP/UDP port number – Typical network application – Strict priority and Weighted Round Robin (WRR) CoS policies – Supports QoS and In/Out bandwidth control on each port – Traffic-policing on the switch port – DSCP remarking – Voice VLAN – Multicast – Supports IPv4 IGMP snooping v1, v2 and v3 – Supports IPv6 MLD snooping v1 and v2 – Querier mode support – IPv4 IGMP snooping port filtering – IPv6 MLD snooping port filtering – MVR (Multicast VLAN Registration) – Security – Authentication – IEEE 802.1x port-based/MAC-based network access authentication – IEEE 802.1x authentication with guest VLAN – Built-in RADIUS client to work with RADIUS servers – RADIUS/TACACS+ users access authentication – Guest VLAN assigns clients to a restricted VLAN with limited services – Access Control List – IP-based Access Control List (ACL) – MAC-based Access Control List (ACL) – Source MAC/IP address binding – DHCP Snooping filters distrusted DHCP messages – Dynamic ARP Inspection discards ARP packets with invalid – MAC address to IP address binding – IP Source Guard prevents IP spoofing attacks – IP address access management prevents unauthorized intruder – Management – IPv4 and IPv6 dual stack management – Switch Management Interfaces – Console and Telnet Command Line Interface – HTTP web switch management – SNMP v1 and v2c switch management – SSHv2, TLSv1.2 and SNMPv3 secure access – SNMP Management – Four RMON groups (history, statistics, alarms, and events)– SNMP trap for interface Link Up and Link Down notification– IPv6 IP address/NTP/DNS management – Built-in Trivial File Transfer Protocol (TFTP) client – BOOTP and DHCP for IP address assignment – System Maintenance – Firmware upload/download via HTTP – Reset button for system reboot or reset to factory default– Dual images – DHCP Functions: – DHCP Relay – DHCP Option82 – DHCP Server – User Privilege levels control – Network Time Protocol (NTP) – Network Diagnostic – SFP-DDM (Digital Diagnostic Monitor) – ICMPv6/ICMPv4 remote ping – SMTP/Syslog remote alarm