PLANET WGS-5225-P82S on teollisuuskäyttöön suunniteltu laajennetulla k’yttölämpötila-aluueella varustettu hallittava 10-porttinen Ethernet PoE+ kytkin. Kytkimen 8x 10/100/1000 kupariporttia on verustettu PoE+ virransyöttötuella. Laitteessa on lisäksi 2x 100/1000 SFP- porttia valokuitumoduleille.

WGS-5225-P82S on rakenteeltaan matala-tyyppinen (”flat”), joten sen seinäasennus on vaivatonta. Laitteessa on myös DIN- sekä magneettikiinnitys mahdollisuudet, joten se saadaan asennettua kaikentyyppisiin koteloihin.

Tekniset tiedot:
• 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with IEEE 802.3at PoE+ Injector
• 2x 100/1000BASE-X SFP slots for SFP type auto detection
• Complies with IEEE 802.3at Power over Ethernet Plus/end- span PSE
• Up to 8 IEEE 802.3af/802.3at devices powered
• Supports PoE power up to 36 watts for each PoE port
• Auto detects powered device (PD)
• Circuit protection prevents power interference between ports
• Remote power feeding up to 100m
• PoE management features
– Total PoE power budget control
– Per port PoE function enable/disable
– PoE admin-mode control
– PoE port power feeding priority
– Per PoE port power limit
– PD classification detection
• Intelligent PoE features
– Temperature threshold control
– PoE usage threshold control
– PD alive check
– PoE schedule
• Compact size with fixed wall-mounted, magnetic wall- mounted or DIN-rail design
• IP30 metal case
• Supports -40…+75C operating temperature
• Supports ESD 6KV DC Ethernet protection
• Dual power input design
• – 48…56VDC wide power input with polarity reverse protect function
– 3-pin terminal block or DC jack connector
• Prevents packet loss with back pressure (half-duplex) and
• IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm Control support
-Broadcast/Multicast/Unicast
• Supports VLAN
– IEEE 802.1Q tagged VLAN
– Up to 255 VLANs groups, out of 4094 VLAN IDs
– Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
– Private VLAN Edge (PVE)
– Protocol-based VLAN
– MAC-based VLAN
– Voice VLAN
• Supports Spanning Tree Protocol
– IEEE 802.1D Spanning Tree Protocol (STP)
– IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
– IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN
– BPDU Guard
• Supports Link Aggregation
– 802.3ad Link Aggregation Control Protocol (LACP)
– Cisco ether-channel (static trunk)
– Maximum 2 trunk groups with 2 ports per trunk group
– Up to 2Gbps bandwidth (duplex mode)
• Provides port mirror (1-to-1)
• Port mirroring to monitor the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching)
• Layer 3 IP Routing Features
– Supports maximum 32 static routes and route summarization
• Ingress Shaper and Egress Rate Limit per port bandwidth control
• 8x priority queues on all switch ports
• Traffic classification
– IEEE 802.1p CoS
– IP TOS/DSCP/IP precedence
– IP TCP/UDP port number
– Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Supports QoS and In/Out bandwidth control on each port
• Traffic-policing on the switch port
• DSCP remarking
• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)
• IEEE 802.1x Port-based/MAC-based network access authentication
• Built-in RADIUS client to cooperate with the RADIUS servers
• TACACS+ login users access authentication
• RADIUS/TACACS+ users access authentication
• IP-based Access Control List (ACL)
• MAC-based Access Control List
• Source MAC/IP address binding
• DHCP snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid
• MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder
• Switch Management Interfaces
– Telnet Command Line Interface
– Web switch management
– SNMP v1 and v2c switch management
– SSH/SSL and SNMP v3 secure access
• Four RMON groups (history, statistics, alarms, and events)
• IPv6 IP address/NTP/DNS management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• Firmware upload/download via HTTP/TFTP
• DHCP Relay and DHCP Option 82
• User Privilege levels control
• Network Time Protocol (NTP)
• Link Layer Discovery Protocol (LLDP)
• SFP-DDM (Digital Diagnostic Monitor)
• Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
• Reset button for system reboot or reset to factory default
• PLANET Smart Discovery Utility for deployment management