PLANET SGS-6310-16S8C4XR on hallittava ja pinottava 28- porttinen Layer 3 -tason kytkin, jossa on 16x 100/1000Base-XSFP-moduulipaikkaa, 8x jaettua 10/100/1000Base-T – kupariporttia (RJ45/SFP) sekä 4x SFP+/SFP-moduulipaikkaa 10GBase-SR/LR tai 1000Base-SX/LX/BX -moduuleille.

Laite tarjoaa suuren porttitiheyden ja 10Gbit/s uplink- kapasiteetin, mikä tekee siitä erinomaisen ratkaisun yritysverkkoihin, palveluntarjoajille ja kampusympäristöihin.

Pinottava rakenne mahdollistaa useiden SGS-6310-sarjan kytkimien yhdistämisen yhdeksi loogiseksi kokonaisuudeksi, mikä lisää joustavuutta ja vikasietoisuutta. Kytkin tukee reititystoimintoja, kuten staattinen reititys, RIP ja OSPF, joiden avulla voidaan rakentaa joustava ja dynaaminen verkkoympäristö. Lisäksi se sisältää kattavat L2/L4-salauselementit, QoS-toiminnot, IPv6-hallinnan sekä ACL- ja 802.1X-tuen.

Luotettavuutta lisäävät redundantti rengastopologia, nopea vikasietoinen palautuminen sekä kahdennettu virtalähde, jotka yhdessä varmistavat verkon jatkuvan toiminnan kriittisissä sovelluksissa.

Tuotepakkaus sisältää SGS-6310-16S8C4XR-kytkimen kahdella sisäisellä 100…240VAC virtalähteellä (ei hot-swap), 19″ räkkikiinnikkeet, RJ45-DB9 RS232 -konsolikaapelin, 2x virtajohdon, SFP-pölysuojat sekä englanninkielisen pikaoppaan.

Tekniset tiedot:
• 24x 100/1000BASE-X SFP ports
• 8x 10/100/1000BASE-T RJ45 copper ports, shared with Ports 1 to 8
• 4x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE- SX/LX/BX SFP
• 1x RJ45 to DB9 console interface for switch basic management and setup
• Hardware Stacking:
– Virtualized multiple SGS-6310 series stacked into one logical facility
– Connects with stack members via assigned 10G SFP+ interfaces
– Single IP address stack management, supporting up to 8 hardware units stacked together
– Stacking architecture supports redundant Ring mode
• IPv4 routing protocol supports RIPv1/v2 and OSPFv2
• IPv6 routing protocol supports RIPng and OSPFv3
• Routing interface provides per VLAN routing mode
• VRRPv1/v3 protocol for redundant routing deployment
• Supports route redistribution
• Supports hardware-based wire-speed VLAN routing
• Supports IPv4 IGMP v1/v2/v3, IGMP Snooping.
• Supports IGMP Fast Leave, MVR, IGMP filter
• Supports IPv6 MLD V1, MLD snooping
• High performance Store-and-Forward architecture, broadcaststorm control, port loopback detection
• 16K MAC address table, automatic source address learning and aging
• Supports VLAN:
– IEEE 802.1Q tag-based VLAN
– Provider Bridging (VLAN Q-in-Q, IEEE 802.1ad) supported
– GVRP protocol for dynamic VLAN management
– Private VLAN Edge (PVE) supported
– MAC-based VLAN
– IP subnet-based VLAN
– Voice VLAN
• Supports Link Aggregation:
– IEEE 802.3ad LACP (Link Aggregation Control Protocol)
– Static mode and LACP mode
– Maximum 64 trunk groups, up to 8 ports per trunk group
• Supports Spanning Tree Protocol:
– STP, IEEE 802.1D (Classic Spanning Tree Protocol)
– RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
– MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
– Supports BPDU & root guard
• Port mirroring to monitor the incoming or outgoing trafficon a particular port (one-to-one and many-to-one)
• Provides port mirror (many-to-1)
• Supports G.8032 ERPS (Ethernet Ring Protection Switching)
• Loop protection to avoid broadcast loops
• Link Layer Discovery Protocol (LLDP)
• Compatible with Cisco UDLD (uni-directional link detection) that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices
• 8 priority queues on all switch ports
• Support for strict priority and WRR (Weighted Round Robin)CoS policies
• Traffic classification:
– IEEE 802.1p CoS/ToS
– IPv4/IPv6 DSCP
– Port-based WRR
• Strict priority and WRR CoS policies
• Supports IPv4 IGMP snooping v1, v2 and v3
• Supports IPv6 MLD v1 snooping
• Querier mode support
• Supports Multicast VLAN Register (MVR)
• Authentication:
– IEEE 802.1x port-based network access authentication
– MAC-based network access authentication
– Built-in RADIUS client to cooperate with the RADIUS servers for IPv4 and IPv6
– RADIUS/TACACS+ login users access authentication
• Access Control List:
– IP-based Access Control List (ACL)
– MAC-based Access Control List
– Time-based ACL
• DHCP snooping to filter distrusted DHCP messages
• IP Source Guard prevents IP spoofing attacks
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• Management IP for IPv4 and IPv6
• IPv4 and IPv6 dual stack management
• Switch Management Interface
– Console and Telnet Command Line Interface
– HTTP Web switch management
– SNMP v1 and v2c switch management
– SSHv1/v2, TLSv1.2 and SNMPv3 secure access
• SNMP Management:
– Four RMON groups 1, 2, 3, 9 (history, statistics, alarms and events)
– SNMP trap for interface Link Up and Link Down notification
• BOOTP and DHCP for IP address assignment
• System Maintenance:
– Firmware upload/download via TFTP or HTTP Protocol for IPv4 and IPv6
• SNTP (Simple Network Time Protocol) for IPv4 and IPv6
• User privilege levels control
• Syslog server for IPv4 and IPv6
• Supports sFlow
• DHCP Functions:
– DHCP Option82
– DHCP server/relay/client
• Network Diagnostic:
– Supports ping, traceroute function for IPv4 and IPv6
– Supports DDM (Digital Diagnostic Monitor)
• Supports ISSU (In-service Software Upgrade) to guarantee