PLANET IGS-6325-24P4S on teollisuuskäyttöön suunniteltu 24-porttinen hallittava 19″ PoE+ Etehernet-kytkin laajennetulla käyttölämpötila-alueella. L3
-kytkin on varustettu 24x 10/100/1000Base-T PoE+ kupariporteilla sekä 4x 100/1000 jaetulla SFP-portilla. Kytkimessä on lisäksi kehittyneemmät hallintapuolen turvaominaisuudet, Modbus TCP sekä IEEE 1588 aikaprotokollatuki aikakriittisisiin sovelluksiin.

Tekniset tiedot – 24x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with IEEE 802.3at PoE+ Injector function – 4x 100/1000BASE-X mini-GBIC/SFP slots, shared with Port-21to Port-24 compatible with 100BASE-FX SFP – RJ45 to RS232 DB9 console interface for basic management and setup – Complies with IEEE 802.3at Power over Ethernet Plus/end- span PSE – Up to 24 IEEE 802.3af devices powered – Supports PoE power up to 36 watts for each PoE port – 440-watt PoE budget – Auto detects powered device (PD) – Circuit protection prevents power interference between ports – Remote power feeding up to 100m – PoE management features – Total PoE power budget control – Per port PoE function enable/disable – PoE admin-mode control – PoE port power feeding priority – Per PoE port power limit – PD classification detection – Intelligent PoE features – Temperature threshold control – PoE usage threshold control – PD alive check – PoE schedule – Modbus TCP for real-time monitoring in the SCADA system – IEEE 1588v2 PTP (Precision Time Protocol) – IP30 metal case protection – 19″ rack-mountable design – Dual 48…56VDC, redundant power with polarity reverse protect function – Active-active redundant power failure protection – Backup of catastrophic power failure on one supply – Fault tolerance and resilience – Supports EFT protection for 6KV DC power and 5KV DC – ESD protection – -40…+75C operating temperature – 2x digital input (DI) – 2x digital output (DO) – Integrate sensors into auto alarm system – Transfer alarm to IP network via email and SNMP trap – Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) – High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth – Storm Control support – Broadcast/Multicast/Unicast – IEEE 802.1Q tagged VLAN – Up to 256 VLANs groups, out of 4096 VLAN IDs – Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) – Private VLAN Edge (PVE) – Protocol-based VLAN – MAC-based VLAN – Voice VLAN – GVRP (GARP VLAN Registration Protocol) – IEEE 802.1D Spanning Tree Protocol (STP) – IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) – IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN – BPDU Guard – Supports Link Aggregation – 802.3ad Link Aggregation Control Protocol (LACP) – Cisco ether-channel (static trunk) – Maximum 14 trunk groups with 16 ports per trunk group – Up to 32Gbps bandwidth (duplex mode) – Provides port mirror (many-to-1) – Port mirroring to monitor the incoming or outgoing trafficon a particular port – Loop protection to avoid broadcast loops – Supports ERPS (Ethernet Ring Protection Switching) – Compatible with Cisco Uni-directional link detection(UDLD)that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices – Link Layer Discovery Protocol (LLDP) – Supports maximum 128 static routes and route summarization– IPv4 dynamic routing protocol supports OSPFv2 – IPv4/IPv6 hardware static routing – Routing interface provides per VLAN routing mode – Ingress Shaper and Egress Rate Limit per port bandwidth control – 8x priority queues on all switch ports – Traffic classification – IEEE 802.1p CoS – IP TOS/DSCP/IP precedence – IP TCP/UDP port number – Typical network application – Strict priority and Weighted Round Robin (WRR) CoS policies – Traffic-policing on the switch port – DSCP remarking – Supports IPv4 IGMP snooping v1, v2 and v3 – Supports IPv6 MLD snooping v1 and v2 – Querier mode support – IPv4 IGMP snooping port filtering – IPv6 MLD snooping port filtering – MVR (Multicast VLAN Registration) – IEEE 802.1x port-based / MAC-based network access authentication – Built-in RADIUS client to co-operate with the RADIUS servers – TACACS+ login users access authentication – RADIUS / TACACS+ users access authentication – IP-based Access Control List (ACL) – MAC-based Access Control List – Source MAC / IP address binding – DHCP Snooping to filter un-trusted DHCP messages – Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding – IP Source Guard prevents IP spoofing attacks – IP address access management to prevent unauthorized intruder – IPv4 and IPv6 dual stack management – Switch Management Interfaces – Console/Telnet Command Line Interface – Web switch management – SNMP v1 and v2c switch management – SSH, TLS, SSL and SNMP v3 secure access – SNMP Management – Four RMON groups (history, statistics, alarms, and events)– SNMP trap for interface Link Up and Link Down notification– IPv6 IP address/NTP/DNS management – Built-in Trivial File Transfer Protocol (TFTP) client – BOOTP and DHCP for IP address assignment – System Maintenance – Firmware upload/download via HTTP/TFTP – Reset button for system reboot or reset to factory default– Dual Images – DHCP Relay and DHCP Option 82 – DHCP Server – User Privilege levels control – Network Time Protocol (NTP) – SFP-DDM (Digital Diagnostic Monitor) – Network Diagnositc – ICMPv6/ICMPv4 Remote Ping – Cable diagnostic technology provides the mechanism to detect and report potential cabling issues – PLANET Smart Discovery Utility for deployment management – SMTP/Syslog remote alarm – System Log