PLANET MGSW-2416F on 24-porttinen SNMP-hallittava ja pinottava L3-tason staattisella reitityksellä varustettu kuitukytkin, jossa on 16x SFP-moduulipaikkaa sekä 8x Gigabitin kupariporttia. Kytkin on varustettu varmennetulla virtalähteellä.

Tuotepakkauksen mukana kytkimen lisäksi virtajohto, asennusohje, RS-232 konsolikaapeli sekä 19″ räkkikiinnikkeet.

Tekniset tiedot:
• 16x 100/1000BASE-X SFP slots
• 8x 10/100/1000BASE-T RJ45 copper ports
• RJ45 to RS232 DB9 console interface for basic management and setup
• 36 to 60V DC, redundant power with polarity reverse protect function
• 0 to 60 degrees C operating temperature
• 19″ rack-mountable
• Relay alarm for port breakdown, power failure
• Two built-in thermal fans
• Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex)
• High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth
• Storm control support
– Broadcast / Unicast / Unknown unicast
• Supports VLAN
– IEEE 802.1Q tagged VLAN
– Up to 255 VLANs groups, out of 4095 VLAN IDs
– Provider Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
– Private VLAN Edge (PVE)
– Protocol-based VLAN
– MAC-based VLAN
– IP subnet-based VLAN
– Voice VLAN
• Supports Spanning Tree Protocol
– STP, IEEE 802.1D Spanning Tree Protocol
– RSTP, IEEE 802.1w
• Rapid Spanning Tree Protocol
– MSTP, IEEE 802.1s Multiple Spanning Tree Protocol, spanning tree by VLAN
– BPDU Guard
• Supports Link Aggregation
– 802.3ad Link Aggregation Control Protocol (LACP)
– Cisco ether-channel (static trunk)
– Maximum 24 trunk groups, with 8 ports for each trunk
– Up to 16Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1) Port mirroring monitors the incoming or outgoing traffic on a particular port
• Loop protection to avoid broadcast loops
• L3: Supports maximum 32 static routes and route summarization
• Ingress shaper and egress rate limit per port bandwidth control
• 8x priority queues on all switch ports
• Traffic classification
– IEEE 802.1p CoS
– ToS / DSCP / IP Precedence of IPv4/IPv6 packets
– IP TCP/UDP port number
– Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Traffic-policing policies on the switch port
• DSCP remarking
• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMP snooping port filtering
• MLD snooping port filtering
• MVR (Multicast VLAN Registration)
• Authentication
– IEEE 802.1x port-based / MAC-based network access authentication
– IEEE 802.1x authentication with guest VLAN
– Built-in RADIUS client to cooperate with the RADIUS servers
– RADIUS / TACACS+ users access authentication Access Control List
– IP-based Access Control List (ACL)
– MAC-based Access Control List (ACL)
• Source MAC / IP address binding
• DHCP Snooping to filter distrusted DHCP messages
• Dynamic ARP Inspection discards ARP packets with invalid MAC address to IP address binding
• IP Source Guard prevents IP spoofing attacks
• IP address access management to prevent unauthorized intruder
• IPv4 and IPv6 dual stack management
• Switch Management Interfaces
– Console / Telnet command line interface
– Web switch management- SNMP v1, v2c, and v3 switch management
– SSH / SSL secure access
• IPv6 address / NTP management
• Built-in Trivial File Transfer Protocol (TFTP) client
• BOOTP and DHCP for IP address assignment
• System Maintenance
– Firmware upload / download via HTTP / TFTP
– Reset button for system reboot or reset to factory default
– Dual images
• DHCP relay and option 82
• User privilege levels control
• NTP (Network Time Protocol)
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Network diagnostic
– SFP-DDM (Digital Diagnostic Monitor)
– Cable diagnostic technology provides the mechanism to detect and report potential cabling issues
– ICMPv6 / ICMPv4 remote ping
• SMTP / Syslog remote alarm
• Four RMON groups (history, statistics, alarms and events)
• SNMP trap for interface link up and link down notification
• System Log
• PLANET Smart Discovery Utility for deploy management
• 100…240VAC / 36…60VDC dual power redundancy
• Active-active redundant power failure protection
• Backup of catastrophic power failure on one supply
• Fault tolerance and resilience
• 2x Digital Input (DI)
• 2x Digital Output (DO)
• Integrates sensors into auto alarm system
• Transfers alarm to IP network via email and SNMP trap