PLANET IGS-6329-8UP2S2X on teollisuuskäyttöön suunniteltu 12-porttinen hallittava DIN-kiskoon asennettava UltraPoE (802.3bt) Etehernet-kytkin laajennetulla käyttölämpötila- alueella. L3-kytkin on varustettu 8x 10/100/1000Base-T PoE++kupariporteilla, 2x 100/1000/2, 5G SFP-portilla sekä 2x 10G SFP+ moduulipaikoilla. Kytkimessä on lisäksi kehittyneemmät hallintapuolen turvaominaisuudet sekä IEEE 1588 aikaprotokollatuki aikakriittisisiin sovelluksiin. IGS-6329 tukee lisäksi raskaampia teollisuuden EMC hyväksyntöjä EN 61000-6-2 sekä 61000-6-4 ja rautatieliikenteen EN 50121-4 hyväksyntää.

Tekniset tiedot – 8x 10/100/1000BASE-T Gigabit Ethernet RJ45 ports with 802.3bt PoE++ Injector function – 2x 100/1000/2500BASE-X SFP slots for SFP type auto detection – 2x 10GBASE-SR/LR SFP+ slots, compatible with 1000BASE-X and 2500BASE-X SFP – 1x RJ45-to-RS232 console interface for basic management and setup – Industrial Hardened design – Dual power input, redundant power with reverse polarity protection – DC 48 to 54V input – Active-active redundant power failure protection – Backup of catastrophic power failure on one supply – Fault tolerance and resilience – DIN-rail and wall-mountable design – IP30 aluminum case – Supports ESD 6kVDC Ethernet protection – -40…+75C operating temperature – 2x Digital Input (DI) – 2x Digital Output (DO) – Integrate sensors into auto alarm system – Transfer alarm to IP network via email and SNMP trap – 802.3bt Power over Ethernet – Complies with IEEE 802.3bt Power over Ethernet Plus Plus Type-4 PSE – Backward compatible with IEEE 802.3at/af PD device – Up to 8 ports of IEEE 802.3af/IEEE 802.3at/IEEE 802.3bt PoE++ devices powered – Supports PoE power up to 95W for each PoE port – Total of 360W PoE budget – Auto detects powered device (PD) – Circuit protection prevents power interference between ports – Remote power feeding up to 100m – PoE management features – Total PoE power budget control – Per port PoE function enable/disable – PoE admin-mode control – PoE port power feeding priority – Per PoE port power limit – PD classification detection – PoE extend mode control to support power feeding up to a distance of up to 160 meters – Intelligent PoE features – Temperature threshold control – PoE usage threshold control – PD alive check – PoE schedule – Layer 3 IP Routing Features – IP dynamic routing protocol supports RIPv2, OSPFv2 and OSPFv3 – IPv4/IPv6 hardware static routing – Routing interface provides per VLAN routing mode – Layer 2 Features – High performance of Store-and-Forward architecture, and runt/CRC filtering eliminates erroneous packets to optimize the network bandwidth – Storm Control support – Broadcast/Multicast/Unicast – Supports VLAN – IEEE 802.1Q tagged VLAN – Supports provider bridging (IEEE 802.1ad VLAN Q-in-Q) – Private VLAN Edge (PVE) – Protocol-based VLAN – MAC-based VLAN – Voice VLAN – GVRP (GARP VLAN Registration Protocol) – Supports Spanning Tree Protocol – IEEE 802.1D Spanning Tree Protocol (STP) – IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) – IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN – BPDU Guard – Supports Link Aggregation – 802.3ad Link Aggregation Control Protocol (LACP) – Cisco ether-channel (static trunk) – Maximum 4 trunk groups with 4 ports per trunk group – Up to 40Gbps bandwidth (duplex mode) – Provides port mirror (many-to-1) – Port mirroring to monitor the incoming or outgoing trafficon a particular port – Loop protection to avoid broadcast loops – Link Layer Discovery Protocol (LLDP) – Compatible with Cisco uni-directional link detection(UDLD)that monitors a link between two switches and blocks the ports on both ends of the link if the link fails at any point between the two devices – Supports G.8032 ERPS (Ethernet Ring Protection Switching) – IEEE 1588v2 PTP (Precision Time Protocol) transparent clock mode – Quality of Service – Ingress Shaper and Egress Rate Limit per port bandwidth control – 8x priority queues on all switch ports – Traffic classification – IEEE 802.1p CoS – IP TOS/DSCP/IP precedence – IP TCP/UDP port number – Typical network application – Strict priority and Weighted Round Robin (WRR) CoS policies – Supports QoS and In/Out bandwidth control on each port – Traffic-policing on the switch port – DSCP remarking – Multicast – Supports IPv4 IGMP snooping v1, v2 and v3 – Supports IPv6 MLD snooping v1 and v2 – Querier mode support – IPv4 IGMP snooping port filtering – IPv6 MLD snooping port filtering – MVR (Multicast VLAN Registration) – Security – Authentication – IEEE 802.1X Port-based/MAC-based network access authentication – Built-in RADIUS client to cooperate with the RADIUS servers – TACACS+ login users access authentication – RADIUS/TACACS+ users access authentication – Guest VLAN assigns clients to a restricted VLAN with limited services. – Access Control Lit – IP-based Access Control List (ACL) – MAC-based Access Control List – Source MAC/IP address binding – DHCP snooping to filter distrusted DHCP messages – Dynamic ARP Inspection discards ARP packets with invalid – MAC address to IP address binding – IP Source Guard prevents IP spoofing attacks – IP address access management to prevent unauthorized intruder – Switch Management – IPv4 and IPv6 dual stack management – Switch Management Interfaces – Console and Telnet Command Line Interface – HTTP web switch management – SNMP v1 and v2c switch management – SSHv2, TLSv1.2 and SNMPv3 secure access – SNMP Management – Four RMON groups (history, statistics, alarms, and events)– SNMP trap for interface Link Up and Link Down notification– IPv6 IP address/NTP/DNS management – Built-in Trivial File Transfer Protocol (TFTP) client – BOOTP and DHCP for IP address assignment – System Maintenance – Firmware upload/download via HTTP – Reset button for system reboot or reset to factory default– Dual images – DHCP Relay and Option 82